ETS Glock Mag

Without a doubt one of the best things about Glock is the aftermarket supporting it- like the AR-15, the options for customization are nearly endless. But along with that comes a brad magazine selection. For many, and myself included for a long time, magazines were something that you stuck to OEM only. Just like parts for my diesels, it was best to stick with factory components if you didn’t want headaches down the road.

Glock mags are famous in that, like the pistol they’re designed for, they are engineered for maximum efficiency and durability. They’re a polymer-over-steel design that borrows cues from combat-grade polymer AK magazines. Why would anyone bother with an aftermarket at all, when the original is ‘good enough‘?

Higher capacity.

Let’s bury this magazine in sand and see what it does to the follower.

The Glock 18 magazine, the famous 33 rounder, for a long while was relatively rare and expensive where you found it. This led to aftermarket copies form Korea that left a lot to be desired. They’re still floating around but I always thought they were junk and never bothered with them after the first one I owned back in the mid-2000s. So I was dubious of any company building them since.

Fully buried. Now lets load some rounds and empty it.

Elite Tactical Systems sought to overcome the stereotype, building inexpensive high capacity Glock magazines that are more than formidable in the durability department. Certainly a tall order. So I picked up a couple from Palmetto State Armory to run through the ringer. Two twenty-two round ETS magazines to drop the hammer on.

No stoppages.

Why twenty two and not the normal 33? Since I have two Gen 3 Glock 19s and that size Glock is by far the most popular model for everyday carry (EDC), the twenty two round mag does not protrude too far from the bottom of the magwell- while it does print, its not obnoxious, and the magazine itself can be easily concealed as a reload once you’ve run through a 15 rounder. A few more rounds than stock without adding a lot of size or bulk. I’ve come to favor it when running through close contact drills.

The biggest thing on my mind, as most seasoned Glock shooters, is the aforementioned durability. The critical component to the design’s legendary reliability is a solid magazine. For my test I picked river sand- its loose, grainy and gets everywhere. And if anything is going to stop a magazine follower, it will. I buried the magazine completely, dug it out, pressed the follower a few times, loaded and emptied it through my 19. No stoppages or failures to feed using mixed steel and brass case ammo.

Now its time to run it over. Since OEM Glock magazines are steel lined for durability, and these are not, I wanted to test whether the feed lips or body would crack under pressure. Since my Superduty weighs somewhere around 6200lbs and 570lb/ft of torque, running them over would be a decent test. I ran the magazine over three times with rounds in it to see if there’d be any damage.

There didn’t appear to be any, so I loaded it up again and got ready to fire. This time the magazine was a bit harder to load- the follower was getting a little bound up on some residual sand. I pressed down hard with my thumb on another round and it broke free. No more issues.

I fired all 22 rounds through the pistol with no problem, slide locking to the rear on the empty mag. While I’m sure some purists out there might still scoff at the fact that its not a factory magazine, it more than passes my own durability test. I don’t have any problems running this magazine as an EDC backup, and at its cost (~$17 as of this writing) its well worth having a dozen or so stashed somewhere.

 

Spread the love
                
By Published On: July 6, 2019Categories: Gear Reviews, NC Scout, Weapons6 Comments on ETS Glock Mag

Share This Story, Choose Your Platform!

About the Author: admin

6 Comments

  1. tropicthunder81 July 6, 2019 at 07:24

    Great test. I concur with the author. I’ve run 12 round ets mags with my g43 and the 31 rounders with my g17 and 19 with no issues whatsoever, even with +1 extensions. They also make ar mags, and are coming out with mags for other guns as well. I’m looking forward to the 40 rounders for g19/17.

  2. Matt in Oklahoma July 6, 2019 at 09:27

    My results were less than spectacular. I contacted them and explained what was going on. Even from the start it would not lock the slide on empty with either of my Glocks. Over time I started to have FTF. I mailed it back to them and they offered to replace it but I declined.
    I hope they’ve got it right and yours continue to work. Between these and SGMs I’ve gone back to only factory.
    The G17 mag with a +2 is 19rds. The 33rd giggle sticks are abundant for now. That will change soon.

    • NC Scout July 6, 2019 at 09:51

      Out of curiosity, when did you buy them? It might be an issue to be aware of out of the older mags. And I take it you’ve had good results with the SGMs? I’ve been hesitant on them because their Saiga mags were trash (and expensive) about a decade ago.

  3. Anonymous July 6, 2019 at 16:29

    5

  4. Matt in Oklahoma July 7, 2019 at 07:28

    I bought them right after they came out. My son said the same thing that they are better during a discussion last night.

    The SGMs I did not have good results with either. There is a large amount of plastic overflow on the inside on the metal liner that doesn’t allow the spring to move properly. I contacted them but they didn’t want to hear about it or see them or to even see pictures. If you use a dremel and a long drill bit the plastic can be removed and then they run ok.

  5. jrg July 8, 2019 at 09:00

    No love for Glock 21 – 30 (.45ACP) ? I hope that changes sometime soon.

Comments are closed.

GUNS N GEAR

Categories

Archives

Spread the love